Fiber proof testers are designed to apply a set load to a fusion-spliced optical fiber to be able to test the effectiveness of the spliced fiber. Our fiber proof testers can be purchased in both linear and rotary designs, for both proof and tension testing. Fiber proof testers are available for single mode, multimode, and polarization-maintaining fibers. Choose from dedicated, standalone systems or multipurpose designs which can be also competent at stripping, cleaning, cleaving, splicing, and/or recoating.
Fiber Recoaters with Proof Testers offer easy, integrated methods to Fiber coloring machine. The fiber recoating process restores the buffer coating to some stripped fiber, offering more flexibility when compared to a heat-shrink protection sleeve, enabling so that it is handled and coiled with no damage to the fusion-spliced section. The integrated linear or rotary proof tester allows users to immediately test a recoated fiber using a pre-determined load and find out the long-term longevity of the fiber. Because of the capacity to restore a fusion-spliced fiber to near original condition, these systems are ideal for applications including undersea optical fiber cables, submarine communication cabling, fiber lasers, or Distributed Bragg Reflector (DBR) lasers.
The procedure begins with the fusion-spliced section of fiber being placed in the center of the mold assembly (see image to the correct). Once set in position, inserts within the fiber blocks secure the spliced fiber in place. Recoat material is pumped to the cavity then UV-cured. The recoated fiber may then be tested by pulling onto it up to a pre-determined load.
Recoater and Mold Assembly Options – Recoaters are available with either a computerized or manual mold assembly. The automatic mold assembly features pneumatic control of the mold plates and it is optimized for top-volume manufacturing applications. Manual mold assemblies, on the other hand, use hinged mold plates that offer more flexibility and are ideal for low-volume manufacturing or R&D applications. An automated or manual volumetric dispensing pump and injection system is employed to inject the recoat material in to the mold cavity.
The PTR208 automatic recoater comes standard with a mold assembly for Fiber drawing machine; For your manual recoaters (Item #s PTR206, PTR206B, PTR307, and PTR307B), the mold assembly is sold separately so that customers can choose the best mold coating diameter for his or her application. Custom mold coating sizes can be found as much as Ø900 µm. Pre-installation of the mold assembly at the factory can also be available. Contact Tech Support to learn more about custom molds or factory assembly.
Most fiber optic cables are designed professionally and are designed to work effectively for a long time. Even though this is the case it doesn’t imply that the units don’t develop problems. As with any other units, the cables develop problems and it’s your choice to recognize and correct them. To assist you here are some of the most common fiber optic fiber problems:
External damage. Common external damages are splits and scratches on the units. The units are highly sensitive; therefore, even the most minor damages have the capacity to prevent effective transfer of signals. In case you have noticed some defects on your units you need to replace them as early as possible.
The optic cable is too long. Optic fibers come in various sizes and lengths and it’s your decision to find the one that is great for your application. In some cases, people install units that are too long than needed. A cable which is too much time reaches the potential risk of winding around itself. An extended unit is additionally at the chance of bending or twisting. These actions often bring about permanent injury to the optic fibers along with its components. To prevent installing the wrong scale of cable you need to take your time to swrwun a measuring tape and measure the distance that you are planning to cover.
Improperly installed connectors. Connectors join 2 or more cables and play a crucial role in determining the potency of the optic cables. It’s common for many contractors to improperly install the cables resulting to cable problems. To fix the problems you need to hire an experienced contractor to install the cables properly.
Stretching. It’s an oversight to get optic cables that are very long. It’s also a mistake to get cables which are short because they are vulnerable to stretching. As i have said, the cables are very sensitive and even a minor damage can prevent the cables from functioning properly. To avoid the cables from stretching you should ensure that you set them up at the right place. You must also avoid pulling the cable jacket during installation. The best way of going regarding it is using grips on the connectors.
Aging. Just like other things under the Fiber drawing machine get old. Old cables are not only ineffective inside their working, they also have a tendency to develop problems every now and then. As soon as your cables are old, the best way of fixing them is replacing them. Our company specializes for making machines that aid you in the making of fiber optic cables. We now have Secondary coating line. We have SZ stranding line and several other units. Go to the given links to find out more.